$20.00 Minimum Merchandise Order - Thank You!

Online Catalog:PanaVise Work Holding Tools :PanaPress

PanaPress PanaVise Model 502 Ideal for pressing bearings, sleeves, collars, forming and assembling small parts, broaching, staking, etc.! Precision ground ram is 3/4" x 3/4" (19.1mm x 19.1mm) and 5 7/8" (149.2mm) long. Four adjustable nylon gibs provide exceptional ram control. Lever arm is 8" (203.2mm) long. Base footprint is 3.7" (94mm) x 7" (177.8mm) Holes 1/4" (6.3mm), countersunk 7/16" (11.1mm) are located at all four corners for bolting to the work surface. Two additional holes are drilled in base plate and screws provided for attaching tooling or for attachment of 506 IDC Bench Assembly Press Retrofit Kit or 561 Crimp Press Retrofit Kit. Weighs 5 lbs. 7 oz. (2.5 kg) and stands 7" (177.8mm) high (not including 8" (203.2mm) arm or ram height).   Price:  $159.95
Retrofit Kit PanaVise Model 506 Convert any PanaPress into a rugged Insulation Displacement Connector (IDC) Assembly Press! Perfect for independent repair technicians and in-house service departments; recommended for low volume, mass termination of various IDC connectors on ribbon cable. Includes shorter lever than standard 502 PanaPress for full lever motion without striking top plate, ribbon cable guide, all mounting hardware and wrenches for ease of installation. Only tool required to complete installation is a medium phillips screw driver. More effective than hand crimpers (completely eliminates the "scissors effect"). This easy to use IDC Bench Assmebly Press helps prevent injuries to the wrist, hands, nerves and tendons. Interchangeable base plates and flat ribbon cable cutter are available. Perfect for independent repair technicians, in-house service departments and value added cable houses; recommended for low volume, mass termination of various IDC connectors on flat ribbon cable.   Price:  $55.49
Retrofit Kit PanaVise Model 561 Convert any PanaPress into a convenient Crimp Press to eliminate wrist fatigue! Accepts all industrial standard crimp die sets. Model 502 PanaPress + this Model 561 Retrofit Kit = Crimp Press Includes longer lever for increased leverage ratio over standard 502 PanaPress, crimp die holders, all mounting hardware and two allen wrenches to ease installation. Only tool required to complete installation is a medium flat blade screw driver. Special needle point allen screws, align crimp dies in upper and lower die holders. More effective than hand crimpers (completely eliminates the "scissors effect") for about the same cost, the 561 Crimp Press Retrofit Kit will accept your current crimp dies, and accepts standard industry die sets. The 12" (304.8mm) lever provides a 20:1 leverage ratio that makes the press easy to use while helping to prevent injuries to the wrist, hands, nerves and tendons. Perfect for in-house service departments, independent technicians and medium-volume manufacturing operations.   Price:  $35.49
Flat Ribbon Cable Cutter PanaVise Model 507 Perfect right angle cuts every time (up to 64-pin conductor cable)! Better then using scissors, as there is no pulling on the inner wires. Easy to operate, slips into the 502 PanaPress with the 506 Retrofit Kit installed. Spring-loaded blade arm returns quickly to original position. Accomodeates ribbon cables up to 3.21875" (81.8mm) wide. Replacement blade is the model 530.   Price:  $64.95
Replacement Blades PanaVise P/N 530 Replacement blades fit the Model 507 Flat Ribbon Cable Cutter. Three blades are included in each package.   Price:  $12.99
IDC Block PanaVise P/N 510 For Female Socket Transition Connectors 2 variations available: 510 & 510-A   Click Here For Drawing Price:  $28.49
IDC Block PanaVise P/N 510-A For Female Socket Transition Connectors 2 variations available: 510 & 510-A   Click Here For Drawing Price:  $28.49
IDC Block PanaVise P/N 511 For Card Edge Connectors 3 variations available: 511, 511-A & 511-C   Click Here For Drawing Price:  $28.49
IDC Block PanaVise P/N 511-A For Card Edge Connectors 3 variations available: 511, 511-A & 511-C   Click Here For Drawing Price:  $28.49
IDC Block PanaVise P/N 512 For Dip Plugs 512 = .100 x .300 & .100 x .600 512A = .100 x .100 mini   Click Here For Drawing Price:  $28.49
IDC Block PanaVise P/N 512A For Dip Plugs 512A = .100 x .100 mini   Click Here For Drawing Price:  $28.49
IDC Block PanaVise P/N 513 For D-Sub Connectors 5 variations available: 513, 513-A, 513-B, 513-C & 513-D   Click Here For Drawing Price:  $28.49
IDC Block PanaVise P/N 513-A For D-Sub Connectors 5 variations available: 513, 513-A, 513-B, 513-C & 513-D   Click Here For Drawing Price:  $28.49
IDC Block PanaVise P/N 513-B For D-Sub Connectors 5 variations available: 513, 513-A, 513-B, 513-C & 513-D   Click Here For Drawing Price:  $28.49
IDC Block PanaVise P/N 513-C For D-Sub Connectors 5 variations available: 513, 513-A, 513-B, 513-C & 513-D   Click Here For Drawing Price:  $28.49
IDC Block PanaVise P/N 513-D For D-Sub Connectors 5 variations available: 513, 513-A, 513-B, 513-C & 513-D   Click Here For Drawing Price:  $28.49
Replacement Guide Arm PanaVise P/N 532 Add an extra guide arm when precision is critical! The replacement guide arm is identical to the guide arm that comes in the Model 506 Retrofit Kit. The use of two guide arms on the 506 Retrofit Kit is prefered by some users versus one for added cable alignment.   Price:  $9.49

Online Catalog:PanaVise Work Holding Tools :PanaPress

Minute Man Electronics

$20.00 Minimum Merchandise Order - Thank You!